TP-Link has always surprised its users with amazing networking devices. Extenders manufactured by TP-Link enable users to get access to a speedy internet connection throughout every corner of the house. But, at times users complain about their range extender not detecting the 5GHz signals of the router. If you are also struggling with the same issue, then walk through this post. Here, we have summed up various tips and tricks to get the problem resolved in a snap. Continue reading.
Fixed: TP-Link Extender Not Detecting 5GHz Signals
Note: Before you try the below-mentioned troubleshooting hacks, ensure that you have configured your range extender via tplinkrepeater.net.
- Reboot the Extender
The primary reason behind the TP-Link extender not detecting the 5GHz WiFi signals are technical glitches. These technical glitches can be overcome by implementing the easiest hack i.e. rebooting. It is called the easiest because you need not be a tech-savvy to reboot the extender.
Here’s how to reboot your TP-Link range extender:
- Switch off your TP-Link extender.
- Let the extender stay idle for some time.
- Switch on your TP-Link extender.
Once your TP-Link extender gets properly rebooted, check whether it detects the 5GHz WiFi signals. If it is still finding it hard to find signals, then consider giving a shot to the next troubleshooting hack.
- Bring WiFi Devices Closer
Perhaps your TP-Link extender and the home router are placed too far from each other which is resulting in poor communication between both devices. To get the problem fixed at hand, consider bringing both WiFi devices closer. However, keeping in mind the location algorithm, do not place both WiFi devices too close. Else, you might indulge yourself in more trouble than you are already endeavoring with.
Note: Apart from bringing the WiFi devices closer, consider switching the connection mode and using an Ethernet cable to connect them. But, remember to use a non-damaged Ethernet cable.
- Update the Firmware
Users often ignore updating the firmware of their TP-Link extenders. It seems that you are also sailing in the same boat. FYI, you need to regularly update the firmware of your range extender to optimize its performance. Thus, without any delay, update your TP-Link range extender.
Here are the do-follow steps to update the TP-Link extender firmware via tplinkrepeater.net:
- Download the latest firmware for your TP-Link range extender.
- Unzip the file if required.
- Now, access tplinkrepeater.net.
- If you come across the tplinkrepeater.net not working issue, use the extender’s default IP address.
- Log in to your extender using the password you’ve assigned to it during the initial setup process.
- On the web-based management page of your TP-Link range extender, click System Tools.
- Select Firmware Upgrade.
- Click Browse and locate the firmware file you’ve extracted.
- Upload the file.
- Let your range extender reboot after the completion of the firmware update process.
- Change the Extender’s Location
Chances are that your TP-Link extender is placed at the location where its WiFi signals are getting interrupted. To prevent this, consider changing the location of your extender. Here’s how to select an appropriate location for your WiFi device:
- Ensure not to place your range extender near fish tanks, mirrors, metal objects, and similar things.
- Make sure that the extender is placed in a well-ventilated room. However, exposure to direct sunlight is prohibited.
- Do you have tracking devices, or transmitting appliances at your home? If yes, then place your extender away from them. To name a few, keep your extender away from televisions, microwave ovens, cellular phones, baby monitors, Bluetooth speakers, treadmills, etc.
- Reset and Reconfigure
If none of the aforementioned troubleshooting hacks has worked in your favor, then there is a high possibility that your extender is partially configured. Thus, you need to complete the setup process. But, for that, you need to restore it to the factory default settings.
To reset your extender:
- Ensure that it is receiving a fluctuation-free power supply.
- Find the Reset button.
- Grab a paper clip and press the Reset button using it.
- Wait until the extender does not get restored to the factory default mode.
Now, access tplinkrepeater login page and set up your extender from scratch. This time your extender will surely detect the 5GHz WiFi signals.
Wrap Up
That’s all about what to do if the TP-Link extender is not detecting the 5GHz WiFi signals. We hope that the troubleshooting tips discussed in this post will help you in fixing the issue in a hassle-free manner.